12v 2000 Watts Powerful Electromagnet using Microwave Transformer - 12v to 220v DC

Hello. I used 12 volts and 12.5 currents. It got too hot after 20 minutes of operation. If I lower the current value, would I use it longer? Will I experience a decrease in my usage power? How much current should I use at most?

You would have had a much easier time cutting just the shallow welds on the side and peeling the top/bottom off (depending on which side they were on).

А ЕСЛИ СВЕТ ПРОПАДЕТ -БЕРЕГИТЕ НОГИ

2000 w? Cuantos Amperios?

Brilliant, well explained. Thanks.

maybeItCanBeUsedToMakePermanentMagnets.

Hi, does polarity matters in 12v power supply

hy sir
i have make it
and watt is not high

its have effect that my power just 1300 VA ( in our country )

Very excellent video. You are a pro

Awesome explanation on how this actually works..thank you so much for that

Only 12 volt, but with high current right?

Isto carrega 300kg

Patetico honbre mentira no crea gente

Cutting slots. ? Would that give more strength than cutting down to primary coil?
Any answers would be helpful.

Thanks

Good job and very interesting. I just sold 2 microwave transformers because I didn't know what to do with them

Cutting the slots would it make stronger if chopped down like on other clips or is this way better strength?

Ok felicitari

Na verdade é só para mostrar o esquema elétrico das bobinas de uma lixadeira Stanley 600 watts 127 volts, mas acho que são todas iguais as ligações para bobina e o desligador, deve ser os mesmos esquema de ligação, obrigado pela atenção, zap 75981663393

Na verdade é só para mostrar o esquema elétrico das bobinas de uma lixadeira Stanley 600 watts 127 volts, mas acho que são todas iguais as ligações para bobina e o desligador, deve ser os mesmos esquema de ligação, obrigado pela atenção, zap 75981663393

If chopped down to top of primary would the magnetic field be stronger? Or surface area better? School teachers anyone? Saw one go 500kg and hold with full mot but only top missing not cut out. 500 kg was max the scale went to.
Cut down to primary or use the surface area slots cut?

20kg is not a lot of weight. Would this work with a 120 volt microwave transformer?

I went through and clicked like on all your videos👍🏻

Don't you realize you are telling same sentence over and over again? It is not joke !

How do you make that not overheat?

Do you need to connect it to DC voltage? Or can you connect it directly to AC voltage?

У наших бичей да и на метало приемке такого ржавого дерьма не найти.Я включила,я смогла,парковка не правильная..Что за перевод?Тайский мальчик,ставший девочкой,но их слишком видать много и уже не знает чем кроме з..или ж.. ну заработать.

अरे इंजिनियर सहाब वीडियो को हिन्दी में बनाया करो

फिर चमत्कार होगा कुछ ही दिन में

।।श्री राधे।।

प्यारे इंजिनियर सहाब

मेरी बात को हल्के मै
ना लेना प्यारे

Puro avle y avle y no acciona

does it have to be DC for magnet to work or it can also be AC

please make the generator

when i was removing mot secondary winding i damaged the primary winding of mot could you tell me how many turns and layers required in mot primary winding plz reply there is no answer of my question on internet.

Can I just say, thank you for leaving in your mistakes and then working it out... its genuinely nice to see a fully honest video that shows its all... and I've seen a few of these posts and builds and this is by far the best 1 to watch and gain information from with a basic shown example of how to build this and make it work...

Great job sir... 👏 👍 👌

Nice 👍🏻👍🏻 🇮🇳 26|03|2022

Just shut up and get on with it.

Knock of the "... guys". It doesn't work for you.

🆎🕉️🕉️GOOD TEACHING FOR YOUR CHANNEL🚦THANK YOU SO MUCH VERY VERY GOOD 👌👌👌👌👍👍👍👍💃💃💃💃

Total waste of a minute a my life watching this chaiwalla damn near electrocute himself. Hey, how bout you put me down for a hundred bucks on pump 10 and a pack a Camel filters and hou get back to work and leave the scary work to those of us who know how to keep from killin ourselves! Now where's my smokes ?

MISTER ELECTRONNNNN

(Google Translate) Beautiful work. I have some questions. 1) If I use two transformers to make a magnetic table, will it be more powerful than if I use only one?
2) If I use two, should I connect them in series or in parallel?
Thank you very much and my congratulations.

Should you back up your power supply's flywheel diode? That's a rather large inductance.

I'm fascinated with electricity and magnetism. Still don't understand it. Don't worry still not playing with it until i have a full grasp. Just trying to find a cheap and easy way to get nails out of burn pit lol

nice video! horrible welding skill though, improve it :D

Nice bead

Qual é a bitola do fio dessa bobina?

What the f*ck is wrong with your camera? It's warping!

Mesmerismusgenerator ?irrsinnige Psychomaschinen ?

Lastima que no entido , el abla