How To Install Your Garage Door Rollers

It's back up.

Kyle...wow ...i am a service tech in s fl and the way u bent the track with vise grips to change the top roller and you jumped when it popped out of the track and then very cooly used the open space to install the roller ....with that light track gauge you could bend it by grabing it and twisting

oh never mind i see you are selling parts and experience and safety

Thanks...couldn't get the missing rollers up to the bend of the track because the same one on both sides were the ones popped out...but it still worked just fine with the door all the way down.

Just ordered these sealed rollers. Great price. I've had nylon rollers (not sealed) for more than 10 yrs now and they are still holding strong, so I can attest to the durability and quietness of these rollers (hell I've replaced about 3-4 springs and not a peep out of the rollers), however for the price of these sealed units, I can't help but replace the non sealed rollers - the price and performance just won't let me keep the old rollers.  


DIYs rollers are about 75% cheaper ($2.40 vs $9.99) than at the place I have ordered parts in the past. I was able to get the entire set for what they wanted for 3 rollers. I now see that they are an over price parts supplier and have found a new supplier.

Thanks DIY

The rollers are great, but the squeeks weren't there. I sprayed and sprayed. Not there. It sounds like it might be the top bearings. They look difficult to replace. Ideas?

When the door is all the way up you can lift the top panel out of the curved piece and slip the roller right out

So why would not lubricate the new roller prior to putting it inside the socket.

Can you insulate your garage door like the one you have Done

That spring is wound to tight

Great!

why did you put the video where the camera was blocked back your arm

A great way not to do A roller replacement no need to bend both tracks second rookie of the year

Thanks about to upgrade my rollers. I do have a question my garage door will not close in the morning I'm assuming the cold... maybe. How can I address this issue? It closes fine any other time during the day only have had the issue early in the morning

take the fucking banner off the bottom while instructions begin

I did mine by taking the side rail off, one of a time while the door is down. No bending.

Great job

Woodglut has very good and accurate plans.

My old 18' wooden garage door is 800+ pounds so I'm not exactly able to do all this "just move the door with one hand while on a ladder" thing. Needless to say I'm not bending or removing track either.

Under such circumstances it seems smarter to use vicegrips to fix a short 2x4 in the track to keep the panels from hinging out and accordion-ing while the wheel is out. But again, each panel of my door probably weighs twice as much as the entire door in this vid.

real bad angle on the camera.

Can't understand what the lubricant is you are using. How about spelling it out?

Kyle, thank you so much for the very helpful videos! I watched the videos for replacing the garage door springs, cables and rollers and they made everythingso easy! Your parts delivery was quick and I couldn't be happier. Thank you for giving me the knowledge and confidence to a job I never would have tried before.

Would bending the top of the track be less problematic to the roller track?

Best video I have seen so far on how to do this job.

lube up the axles on the new wheel before you install them and also lube up the hole they go into ... be sure to clean the entire track too and spray lube the tension springs to quite them down

Wasn’t as quick since you’re a pro, but this video was great. Took about 20 minutes to replace them all and save myself a trip from the repair guy. New rollers look great!

excellent

very educative. Thank you .Regards

Nice content but the video could be so much better if your arm wasn't in front of what we need to see. Also this and other videos the banner obscures the view of what you are doing. Thanks a lot for the video but if you could address these two issues in coming videos that would be great!

I need a garage door opener for all star. Can you buy these and bond it to your garage door opener how do you replace it?

Great video. I would add that it be a good idea to lubricate the new roller pins before inserting them.

How to redo spring & side Tension wheels?

Your arms are in the way

I really want to learn garage tune ups thank you