Class II composite restoration (2) – Horizontal incremental technique (#26) - Arabic عربي

Class II resin-based composite restoration using the horizontal incremental technique on a maxillary first molar (#26)

- To learn about class II resin-based composite restoration using the slanting/oblique incremental technique, watch the video: https://youtu.be/TVOS0iYwQPA

- To learn about class II occlusal cavity outlines for maxillary and mandibular premolar and molar plastic teeth in Preclinical Operative Dentistry, watch the video: https://youtu.be/-CSU6VENaE8

- To learn about class II cavity preparation for composite on a maxillary molar, watch the video: https://youtu.be/T6QFImvHtEU

- To learn about Enamel & dentin bonding / adhesive systems (3-step, 2-step, 1-step) & application, watch the video: https://youtu.be/yFf08V5BVGA

- To learn about class I resin-based composite restoration using the horizontal incremental technique, watch the video: https://youtu.be/1imu0hwsX8k

- To learn about resin-based composite cavity preparation & restoration instruments and tools setup, watch the video: https://youtu.be/7VviHVO3ViA

- To learn about finishing & polishing tools & application for class I & II resin-based composite restoration, watch the video: https://youtu.be/0m2H94SLtQI

- To learn about how to check occlusion after restoring a cavity preparation, watch the video: https://youtu.be/BGsyo4sAmcs

Subscribe for more Preclinical Operative Dentistry videos: https://www.youtube.com/channel/UCRrP40XBiD6v0ne61McFj0Q

Music: https://www.bensound.com

---- Contents of this video ----

00:00 – Introduction
00:14 – Title: Class II resin-based composite restoration – Horizontal incremental technique (Mandibular first molar)
00:24 – Class II resin-based composite restoration – Horizontal incremental technique
00:37 – Place the matrix band & wedge
01:47 – Check that the gingival margin is sealed using a dental explorer
01:51 – Apply the adhesive system (Two-step etch and rinse system): a. Acid etch
02:48 – Apply the adhesive system (Two-step etch and rinse system): b. Primer + Bond
03:43 – Apply/adapt/place/press/pack/tap composite material: 1. Proximal box (convert class II to class I): a. Adapt in the floor
04:32 – Apply/adapt/place/press/pack/tap composite material: 1. Proximal box (convert class II to class I): b. Remove excess using a dental explorer held at 45 degrees
05:12 – Apply/adapt/place/press/pack/tap composite material: 1. Proximal box (convert class II to class I): c. Light-cure according
05:26 – Apply/adapt/place/press/pack/tap composite material: 1. Proximal box (convert class II to class I): d. Place the following increment. e. Create the marginal ridge
07:10 – Apply/adapt/place/press/pack/tap composite material: 1. Proximal box (convert class II to class I): f. Remove excess using a dental explorer held at 45 degrees BEFORE curing
08:08 – Apply/adapt/place/press/pack/tap composite material: 1. Proximal box (convert class II to class I): g. Light-cure according to the manufacturer’s instructions
08:18 – Apply/adapt/place/press/pack/tap composite material: 2. Occlusal part: a. Apply and adapt an increment (Horizontal increment)
08:47 – Apply/adapt/place/press/pack/tap composite material: 2. Occlusal part: b. Light-cure
08:59 – Apply/adapt/place/press/pack/tap composite material: 2. Occlusal part: c. Apply and adapt the following increment
09:29 – Apply/adapt/place/press/pack/tap composite material: 2. Occlusal part: d. Create anatomy
10:27 – Apply/adapt/place/press/pack/tap composite material: 2. Occlusal part: e. Light-cure
10:38 – Apply/adapt/place/press/pack/tap composite material: 2. Occlusal part: f. Add increments, create anatomy, and light-cure as needed
11:30 – Apply/adapt/place/press/pack/tap composite material: 2. Occlusal part: g. Pack the distal part, create anatomy, and remove excess
12:31 – Apply/adapt/place/press/pack/tap composite material: 2. Occlusal part: h. Light-cure
12:45 – Check the restoration margins for gaps, ditches, and excess
13:18 – Remove the matrix band and wedge
14:02 – Additional curing proximally from the buccal and lingual directions AFTER matrix band removal
14:34 – Flake off excess bonding
14:52 – Check the marginal ridge height, contour, contact, no overhang, margins, anatomy, and surface texture
15:19 – Check contact
15:45 – Finishing and Polishing: Finishing: Using diamond points with water coolant
16:59 – Finishing and Polishing: Finishing: Check the marginal ridge height, contour, contact, no overhang, margins, anatomy, and surface texture
17:19 – Finishing and Polishing: Polishing: using rubber points with water coolant
17:48 – Check the marginal ridge height, contour, contact, no overhang, margins, anatomy, and surface texture
18:01 – Check occlusion

Instagram: @afnanalzain
Twitter: @afnanalzain
Telegram Channel: Dr. Afnan O. Al-Zain / t.me/afnanalzain
Email: [email protected]

Скачать видео