Тэги:
#Hunting #fishing #hog_hunting #pig_hunting #outdoors #shooting #pig_shot_placement #shot_placement #rifle #bass #bow_hunting #bowhunting #bowhunting_hogs #bowhunting_pigs #mechanical_broad_heads #fixed_blade_broad_heads #Ashby_Bowhunting #high_FOC #heavy_arrows #single_bevel #cut_on_contact #bowhunting_deer #sharpening #lighted_nocks #Arrow_building #How_to_build_arrows #Install_insert #Ethics_Inserts #How_to_install_inserts #Build #Arrows #Heavy_arrow #archeryКомментарии:
Good to see you
ОтветитьThose arrows are garbage.
ОтветитьI’ve had some do that and was able to heat it up and pull it out. Worked good on a few then damaged the arrow on one so I quit doing it
ОтветитьI was litteraly about to look this up! Thanks so much
Ответить🤣🤣🤣
Ответить💪🏽🇺🇸🏹
ОтветитьGood advice.
ОтветитьHey Troy I’ll be in central Texas for work soon I was wondering if I could stop by?
ОтветитьI this this to my Apollo’s I bought and luckily I had slower settings epoxy and I realized what I had dove and why before it set up.
ОтветитьEh I was just watching you strop awesome!
ОтветитьWhy didn't you post this Friday when I built my arrows... 😭
ОтветитьYup,,,,, Been there done that 👍
ОтветитьThat banging them out trick works great. I took a nail that was straight & long for the weight. It fits inside my micro shafts after I cut the head off square. The square end goes against the insert. Better to have more weight than to heat your tip up too much. It has worked on JB Weld & AAE Max Impact. If it works on them it will work on any glue.
ОтветитьI would have never thought about that. You literally run a PhD course in arrow building.
ОтветитьThat was gold
ОтветитьI used gorilla glue epoxy and I have more inserts come out that ever before… any recommendations?
ОтветитьPro tip for 12 year olds.
ОтветитьProud donor of the ASHBY foundation
ОтветитьI just created an air biscuit.
ОтветитьIsn't there a hole all the way through the insert?
ОтветитьWhy do you epoxy them in over hot melt glue? Ive had epoxied inserts fly out but have yet to have a hot melt insert fly out.
ОтветитьI always wait til I goto nock tune before I put the nocks in
ОтветитьThanks Troy I'm now shooting adult arrows.
ОтветитьYour shooting my arrows now just got the 2nd dozen In today
ОтветитьChange things up to low heat hotmelt. Then you can change your inserts when you please.
ОтветитьTroy learns by school of hard nocks
ОтветитьCan you still use the drill bit trick to knock them out when there epoxy Troy?
ОтветитьIs that in cases where epoxy gets over the end of the insert? There is a hole straight through the insert, wouldn’t the air just escape through the hole where the threads are? Unless epoxy gets over that hole, which really shouldn’t happen. Thanks. Love the content
ОтветитьIs that r22 on the shelf? How much? 😂🤣
ОтветитьNice quick tip there Troy. I have an arrow or two where the outsert is like that with a gap. Could be from the air piston or multiple shots into a target. When I reinsert it I will remember to remove the nock. Thanks again Troy.
ОтветитьLOL, that's happened to me before. Jameson seems to work better than coffee.
ОтветитьSome solution are after mixing the epoxy wait a while an let it get thick instead of slimy. It will have more tac to it. My easton deep six inserts have a hole on both sides so are cant get trapped when inserting. But ive always naturally remove everything from the shaft when gluing. Shit happens tho.
ОтветитьIs use of epoxy to secure inserts a “must do” on high FOC setups to ensure arrow integrity? I have been using cool melt to allow for making adjustments and haven’t had any issues with inserts coming lose but I haven’t sent them through many critters or heavy bone either.
ОтветитьI can’t believe the ranch fairy made that mistake
Ответитьhmmm a hole in the nock???? little tiny one??
ОтветитьGood to know!
ОтветитьSince you are always looking for penetration, visiting Demolition Ranch would be interesting to see how heavy arrows go through different objects. He is kind of know for penetration testing of objects. How many {insert object here} does it take to stop a .50 cal? He is in the same town.
ОтветитьHey I was wondering if you have ever considered spray paint or a spray on dry lube for your broadheads after you have sharpened them?
ОтветитьSo I bought the Iron will all steal hit insert system 🤑, and like and idiot I stoud them up over night and the inserts slid in deep enough that I couldnt even get my points to start to screw in... well after a week of working with a sottering iron and some unique pulling techniques I got them right, would recommend it though lol
ОтветитьBowshop guys hate me now. Hhaa ha<-- Ranch fairy laugh
ОтветитьCan you please make a video for new guys I’m overwhelmed with all these terms and lingo and what I should be shooting for whitetail lol please help
ОтветитьThe best results I have ever had/have is with the blue low heat hot melt. I clean the inside shaft with q-tips and 91% alcohol. I wipe the insert down with alcohol too. I very very seldom have a insert come loose. I believe in the last four years I've had two slip a little but not lost. And if you like to align broadheads with vanes just apply only enough heat to loosen the hot melt and rotate as needed. Works perfectly fine.
ОтветитьI never thought of that. I always thought it was from hitting something hard
ОтветитьShit happens sometimes ... 🤷 😆
ОтветитьI put my nocks in first, and I'm happy I didn't try gluing. But... I have to take those bad boys out, I had them all tuned to the arrows bend. Damn
Ответить