Комментарии:
It's better to just buy a blade from the Custom Saber Shop, they got color blades for sell for just about $13.95, you can get 2 of them for just little over $30 or so and blade tips for little over $4 and all you need to do is just drill a small hole in the blade emitter for a blade tension screw, get the Alan Wrench screw version of screws not regular screws because reg. screws chew up the blades like Termites to wood..
ОтветитьI hate witchcraft
ОтветитьPro tip for stickers on metal. Use a lighter or small torch, hold it up to the sticker for like 10-15 seconds. The whole sticker should peel right off very easy.
Ответить👍 This is cool. Super dope. Loving this. Very creative. Well done my friend.
ОтветитьCool stuff, thanx. MTFBWY
ОтветитьA ten minute lightsabre in 18 minutes..... make it make sense
ОтветитьFun, cheap cosplay project.⭐️
ОтветитьI hate you🤬
ОтветитьI hate you. You are the worst. I did not give you any. It did not give me any help. You’re the worst.
ОтветитьDIY lightsaber in 10 minutes but with an 18 minute video x3
ОтветитьAll real jedi make their own lightsabers.....
ОтветитьVentilation for rubbing alcohol 😅
Ответитьit would be cool if you added a hook for the belt
ОтветитьLooking good. Good luck though, when you need to change batteries 😅
ОтветитьYou should use a transparent acrylic plastic tube and sand it to diffuse it then put coloured cellophane inside it
ОтветитьLooks awesome but you should use a white blade and cut out a small bit of colored sheet to put over the flashlight
ОтветитьMe, who is a broke teenager and knows nothing about this stuff, omw to attempt to make two of these for my ahsoka cosplay
ОтветитьConsidering most of the sci fi do dads especially in the og star wars movies were all kitbashed this is actually incredible authentic to most of the original lightsabers
Ответитьalso a good source of getting stickers off is a heat gun or blow dryer. and leaves no residue
Ответить.... no
ОтветитьThis looks simple and affordable. I pinned this on my pinterest and added your link.
ОтветитьPut it on boiling soap water to remove stickers
ОтветитьPut a reflective rod inside the saber it will help
ОтветитьCan I get a full detail list of the materials? I dont quite know what all the things you're using.
ОтветитьThis is pretty cool! Thank you!
ОтветитьHow long have you had the piece of pipe from the big K, haven't seen them in years.
Ответитьtry taking a needle and puncturing alot of random holes to allow the light to reflect from.
Ответитьyou forgot the kyber crystals
ОтветитьUse plumbers tape around threads and it makes it snug as a bug.
ОтветитьBecause Harry Potter is Star Wars with sucky lightsabers… 😂😂
ОтветитьWhen you realize making a diy lightsaber is also how you make a lightsaber in starwars
ОтветитьDope video
Ответитьthis is so cool
ОтветитьUse a hair dryer to remove the stickers from any of your parts leaves no sticky residue
ОтветитьUsing Vaseline to remove the sticky residue also works well
ОтветитьIs it durable
Ответить😂😂😂😂
Ответитьthank you I need this video
ОтветитьLove it gonna try making one myself.
ОтветитьDon’t lie and say 10 mins man. It’s good. Just call it what it is. No need for clickbait nonsense.
ОтветитьThat's sick.
ОтветитьThe best way to get the sticker office to use WD-40 and let it saturate, and then it just slides off easily!
ОтветитьMark my words, I’m saving this for when I’m older to make.
Ответитьolive oil from your kitchen will remove the glue from stickers. :)
ОтветитьPlastics scrapper with alcohol will not scratch it at all.
ОтветитьThe handle is very good improvised and cheap. The blade not so much, it's the same cost to buy a Pvc frosted tube and strip of back adhesive leds
Ответитьpolycarbonate tubing, it can be a little expensive, but will make a way better blade and as long you fix it well enough, you can wack it into almost anything without breaking it
ОтветитьFunny, I made a light saver this week using this method sorta without watching a video just soley using my creativity, I used these 4ish inch clear tubes I had from disposable vapes, and I then taped tracing paper around the tubes and colored them, the only issue I had is I had to use 5 tubes and u can kinda see that, it was also sorta difficult to attach the first one to the flash light
ОтветитьWhere u get your parts
Ответить