Edward Niedziejko

One side slotting - slots are 8-10mm for a 6mm bit so the bit doesn't rub on both sides. 02:40
One side slotting - slots are 8-10mm for a 6mm bit so the bit doesn't rub on both sides. Edward Niedziejko 2,193 2 года назад
PrintNC partial retract for deep drilling, 9k rpm, 250mm/min feed, 0.5mm stepdown, 5mm retract. 00:22
PrintNC partial retract for deep drilling, 9k rpm, 250mm/min feed, 0.5mm stepdown, 5mm retract. Edward Niedziejko 1,463 3 года назад
PrintNC wasteboard surfacing with 3/4" bit at 10m/min 1mm doc 15mm stepover 00:16
PrintNC wasteboard surfacing with 3/4" bit at 10m/min 1mm doc 15mm stepover Edward Niedziejko 2,777 4 года назад
PrintNC narrow slot chip removal fan 00:12
PrintNC narrow slot chip removal fan Edward Niedziejko 3,951 4 года назад
final chamfer pass on a pair of PrintNC plates for other builders. 01:46
final chamfer pass on a pair of PrintNC plates for other builders. Edward Niedziejko 1,984 4 года назад
PrintNC bore op: 0.75mm step down/rev, 22krpm, 1800mm/min feed, 6mm single flute in 6.5mm hole. 00:30
PrintNC bore op: 0.75mm step down/rev, 22krpm, 1800mm/min feed, 6mm single flute in 6.5mm hole. Edward Niedziejko 2,139 4 года назад
PrintNC nut block pocket op: 3200mm/min, 22k rpm, 1mm stepdown. 22mm w by 20mm d. DLC coated 6mm. 01:03
PrintNC nut block pocket op: 3200mm/min, 22k rpm, 1mm stepdown. 22mm w by 20mm d. DLC coated 6mm. Edward Niedziejko 6,437 3 года назад
@PrintNC electronics cabinet rebuild with new VFD (not shown) and GrblHAL2K EST. 02:25
@PrintNC electronics cabinet rebuild with new VFD (not shown) and GrblHAL2K EST. Edward Niedziejko 1,037 2 года назад
Short explanation for setting G54 work offset. 01:08
Short explanation for setting G54 work offset. Edward Niedziejko 265 2 года назад
sensor board and touch probe test 00:31
sensor board and touch probe test Edward Niedziejko 330 4 года назад
PrintNC drilling 5mm 2 flute, 9k rpm, 250mm/min, 0.75mm peck, 3mm partial retract, 24mm total depth. 01:40
PrintNC drilling 5mm 2 flute, 9k rpm, 250mm/min, 0.75mm peck, 3mm partial retract, 24mm total depth. Edward Niedziejko 3,146 3 года назад
PrintNC 4m/min roughing aluminum, 2.4mm stepover, 2mm doc, 22k rpm 01:29
PrintNC 4m/min roughing aluminum, 2.4mm stepover, 2mm doc, 22k rpm Edward Niedziejko 8,166 4 года назад
PrintNC pocket op for Z plates, 3200mm/min, 19k rpm. 01:14
PrintNC pocket op for Z plates, 3200mm/min, 19k rpm. Edward Niedziejko 3,445 3 года назад
PrintNC 4m/min, 5mm stepover cutting a topography in 3/4" plywood pt 2 03:15
PrintNC 4m/min, 5mm stepover cutting a topography in 3/4" plywood pt 2 Edward Niedziejko 633 4 года назад
PrintNC 12m/min rapids demo 00:17
PrintNC 12m/min rapids demo Edward Niedziejko 11,765 4 года назад
PrintNC 4m/min, 5mm stepover cutting a topography in 3/4" plywood pt 1 02:19
PrintNC 4m/min, 5mm stepover cutting a topography in 3/4" plywood pt 1 Edward Niedziejko 1,041 4 года назад
Voron Trident startup: home XYZ, 3 point bed level, purge/brush nozzle, auto Z, final quick wipe 01:55
Voron Trident startup: home XYZ, 3 point bed level, purge/brush nozzle, auto Z, final quick wipe Edward Niedziejko 2,675 3 года назад
PrintNC adaptive clearing, both ways 2mm stepdown, 5.7mm stepover, 22k rpm, 3200mm/min w DLC 6mm 02:08
PrintNC adaptive clearing, both ways 2mm stepdown, 5.7mm stepover, 22k rpm, 3200mm/min w DLC 6mm Edward Niedziejko 1,980 3 года назад
PrintNC 5mm carbide drill chip breaking 1mm peck .1 retract, 8k rpm, 160mm/min plunge 01:27
PrintNC 5mm carbide drill chip breaking 1mm peck .1 retract, 8k rpm, 160mm/min plunge Edward Niedziejko 3,041 3 года назад
PrintNC Z plate jig for back side chamfers 03:23
PrintNC Z plate jig for back side chamfers Edward Niedziejko 934 4 года назад

Сейчас ищут