MN82 LC79 Motor Upgrade

Thank you for this information. I was hoping this could be done. 👍

People say,if i want to change the motor,i need to change the esc too..is that true?

Nice mod. Its even better if you do the brushless mod and all the electronic

Hello. Can you please provide me a link for a 370 motor with long shaft. Couldn't find it.
Thanks

Awesome video! I have several MN78, one MN99s, and plan on getting the MN82. All of them need upgrades to improve performance and reliability. I appreciate this information.

Applicable po sa MN99s? planning to upgrade the motor. newbie here. thanks po

Hi bro do you use 370 motor with high rpm o low?

Good video...nice infomation...👍👍👍

One more thing bro, could you tell me what is the motor driver IC on the MN82 stock ESC/receiver? I saw TA6586 on the MN9x/MN78 board, is it still the same? It's the DIP-8 chip next to the motor connector. Trying to figure out the max amp draw I can safely pull through the stock electronic (if it's the same, datasheet says 5A continuous and 7A max but may need heatsinking on the motor ouput legs)

Lastly, it just occured to me but do we need that spacer/adapter? Otherwise can't we just drill 2 holes on the plastic housing and use a more standard 10-11.5mm shaft motor?

Is the top speed any faster or slower with the 370 installed? Thank you!

How many rpm does a 370 motor use? I want the same rpm as yours.

Just received my MN82 today, ok woah they've replaced the motor driver from the MN9x boards, it used to be the TA6586 5A continuous, 7A peak with the SA8336 which can handle 7A continuous, 14A peak (if you can trust chinese datasheet), with a bottom heatsink pad, both are pin compatible but if you want to be able to heatsink it, you'll have to solder it upside down so you can stick a heatsink below lol

Just found you and subscribed. Great informative videos. Thank you.

very nice explanantion. im just waiting for my mn82 to arrive.. changing the motor sure my 1st thing to do

Where did you get the adapter plate?

Any brushless motor fit in mn82?

Excellent work..!

Are you used motor from the link?
How long his shaft is ?

You can get a 370 motor with a 2 speed gearbox and driveshafts so why not just install that ?

This is a fantastic video. Did you run the 370 off the standard electonics?

Is it possible to install an esc with the standard reciever etc for the 370?

Bro nagpalit ako motor na 370 same ng sayo. Bakit parang ayaw nya magstart umandar parang pigil sa low throttle tas pag inikot mo ng kamay dun lang sya aandar

need pa ba re-solder?

What is mn82 stock motor shaft size? Is it 2 mm?

Salamat po.. im new to this. Unang upgrade ko to

Hey bro, please new link for the motor. It's unavailable

Brasil 🚜👍

Hi,

really nice vidéo!!!!

did you keep the pignon who was on the 280 motor?

Sorry, last question, the link for the motor don't work, have you another link for a 370 motor for MN82 please?

Thanks in advance 🙂

can i do this upgrade in wpll c24 wiithoutu changing electronics? or changing metal axle and rods in to metal?

Nice conversion on motor to gain more power or to ran smoothly?? Did you change also the ESC or your still using the original

Nice 👍 is it possible to increase the signal range/ control range of mn82 ?

with the motor upgrade, how much does it last the original battery?

Hello and thank you again for the great guide. I've made the motor change. Motor is working fine and smooth but when I connect it with the wheels, the wheels are tugging. I've tried to turn the joint with wheels and it seems to helps but I'm not sure if it is as the original state. So I would like to ask you if am I correct that it is necessary to correctly set (turn correctly) the plastic (original) connection to the motor. Thank you very much in advance.

Tiene la electrónica de fábrica?? Yo le puse un motor 370 y no me va bien no se porque??

Very cool! What's the approximate top speed (with stock motor) of this pickup? Can it go up to 10 km/h?

Very well done 👍
Thank you

Qual melhor motor pra MN 82?

Hello sir.

I have a question.

I have changed the motor with the metal gearbox, the ESC, even the receiver to use it in my transmitter, but I can't get it to work at anything other than a single speed and it's fast. Do you know if there's a way to configure two speeds like with the original electronics?

Thanks for your videos.

What I have to do to make my MN82 more faster and more smoother than stock? 😉

I tried 2 different 370 motor on my MN82 but unfortunately it doesnt accelerate properly again put the 280 back in place 😶

Iz it fine to upgrade all parts with metal with a stock motor?

👍

Question lang sir kelangan din ba upgrade into metal gear ito? Nag jejerk kasi sya sa low speed and sometimes high speed all stock esc

Question lang sir kelangan din ba upgrade into metal gear ito? Nag jejerk kasi sya sa low speed and sometimes high speed all stock esc

Ok sir salamat po ung nabibili po ba sa shopee na 30a pasok na po ba un

Bro will it be fine if my gears stay plastic other than metal?

sir i have a question, i ordered a 370 motor(blue color back side) from aliexpress. i plugged it to my stock circuit. it does not rotate continuously. when trigger press, it start to rotate, 2 sec later stop and after 2 sec start again then again stop. it's repeating. after i checked my circuit, it's heating high. there is no circuit heating with stock motor(280). sir can you explain why?😢